|Showing off all four parts
of my upcycle project with
my favorite pal! See my poor
tomato plant in the back?
I sew too much to have
time to garden, oops.
This is going to be four posts, each covering how I upcycled two pairs of jeans and a pair of dress pants. I’m steadily trying to sew my way through the giant pile of clothes that Daddy B gave me to upcycle.
I like this project because I’m trying to use all parts of what I upcycle, as much as I can. When I was in elementary and middle school, I was fascinated by how people throughout history used all parts of an animal so as to produce less waste. I really haven’t stopped being fascinated by this. I still really enjoy books that discuss how people have or may have done this, such as in Jean Auel’s Earth’s Children series (fiction, but really well thought out fiction).
Imagine how little waste we would have if we could do this more in our society. Plus, scraps of the same materials help make excellent coordinating accessories. Nothing will ever match quite so well as the same materials! I’m usually terrible about accessorizing- maybe this will help me coordinate better in the future!
The four parts of the blog will include a skirt, bandana, purse, and bracelet. I think I may even have a left material left over to make something else too! Exciting!
Here we go…
Part I: Skirt
First- if I turn Daddy B’s pants into a cute skirt for me, does that mean *I* wear the pants in this family? Teehee… Ok yes, bad joke! I couldn’t resist though!
Cut your pants apart. I cut off the legs and then cut the legs open.
Cut out 5″ or 10″ width pieces of the pants and jeans. I just did a bunch of these two sizes.
Iron your fabric. Probably doing this before cutting it would be wise, but whatever.
Take two pieces, face them right sides together and sew along one long side with a 1/4″ seam allowance. I kept adding on pieces until I had one huge rectangle with lots of pieces all sewn together.
I didn’t think I had enough strips of fabric to not use one of them so I decided to cover a hole in one of the strips with an extra heart appliqué I had laying around so I didn’t waste any of my fabric. Not going to give my screwed up directions here because I’m not certain I did it the way I was supposed to… so far it’s holding up, but you should just find a good tutorial on making patches or appliques if you want to do this too.
I went back to my strips of fabric sewn together and zig zagged all of the raw edges to prevent fraying. Serge if you have that option.
I also top stitched each strip as well. I made sure the extra fabric that I zig zagged was all in one direction, then did a straight stitch to finish it.
I didn’t like how it looked as just a rectangle so I decided to make the waist smaller than the bottom. I had no clue what I was doing. I decided to measure the biggest part of my bottom half- in my case, my hips/butt, to figure out how wide the waist needed to be so I could pull the skirt up to put it on. Jean isn’t very stretchy and I was using a drawstring to hold it up so it needed to be big enough to squeeze into! I added a couple inches to that in order to account for seam allowance.
The chalk line shows where I cut it.
I put the ends of my rectangle together, right sides of the fabric facing each other, and sewed a straight stitch up the side with another 1/4″ seam allowance. I finished this with a zigzag and top stitch, similar to the other pieces. You should now have a “skirt” with no finished seams at the top or the bottom. Give it a try- pull it on. It should fit.
Next you’re going to add a casing at the top for your drawstring (waist). I just folded under the top fabric twice and top stitched to close the casing. Leave a small area to feed your drawstring through. I used teeshirt yarn for my drawstring (yay for more upcycling!) and attached a safety pin to the drawstring, feeding it through one side until it came out the other. I made sure I had enough string, cut the sides even, and tied a knot on each side.
You might want the drawstring on the outside, but I like it on the inside so I don’t have a little bunch over my tummy to pucker out my shirt… that annoys me. It looks goofy. I didn’t want to cut holes in my fabric (haven’t figured out how to do button holes yet) so I just fed the strings through the bottom of the casing, then did a stitch in between the two strings.
I decided to add a pocket at the last minute. I seam ripped a pocket from one of the pants and then just stitched it onto the back of my skirt. I had to zigzag the bottom of it on because it was fraying. Probably should’ve picked up some matching thread, but whatever. Haha, I’m so lazy.
To finish my skirt, I just folded over the bottom twice and top stitched to create a finished seam.